You bought a new disposal, climbed under the sink, and found the old mounting hardware does not look like the new one. Or you want to keep the old mount to save a step, and the box does not say whether that works. The garbage disposal sink mount is the part that decides it, and a flange, a complete mounting assembly, a cushion ring, a gasket kit and a conversion adapter are five different purchases.
The short answer: read the model off the disposal’s label, work out which mount family you have, and match both to the maker’s own documents. This page covers U.S. residential disposals from InSinkErator, Moen, Waste King, GE and a few others. It does not cover commercial units, drain plumbing beyond the discharge, or electrical work.
Read the Label Before You Touch the Mount
Identify three things separately: the complete model of the disposal, the mounting assembly already under your sink, and the replacement you plan to install. Similar-looking mounting hardware does not establish that two parts interchange. Waste King’s FAQ tells you to have your model number ready and to check the technical specification page for your model, and Moen’s selection guidance tells you to consult the specification sheet for the model you are considering for detailed measurements (Waste King FAQ, Moen: Choosing a Garbage Disposal).
Where to look varies by brand. These locations come from the makers’ own pages, but no single spot holds for every unit, so treat them as places to check:
- InSinkErator: a gray tag near the bottom. The maker’s warranty page shows photographs of older and newer labels (InSinkErator warranty).
- Moen: the model is printed on the side, with a model and serial plate underneath (Moen identification guide).
- Waste King: a model and serial label on the bottom. Decide whether you have EZ Mount or Pro 3-Bolt before you pick hardware (Waste King FAQ).
- GE: the exterior bottom, checking all around the bottom front edge, according to GE’s locator (GE label locator). Copy the complete model suffix.
- American Standard/Joneca: a bottom label in the cited manual. Check whether your assembly follows the threaded Speed Master instructions or the three-bolt instructions (Joneca owner manuals).
- KitchenAid: the bottom of the disposer, then the maker’s owner center (KitchenAid owner center).
If the label is hard to photograph, InSinkErator’s installation manual tells installers to detach the removable specification-label portion and keep it somewhere visible, so look for it on the packaging paperwork too (InSinkErator installation manual).
Look at the Mount Itself
Appearance suggests a candidate mount interface. It does not name an exact model. Waste King distinguishes its EZ Mount, which has plastic mounting components and a removable splash guard, from its Pro 3-Bolt, which has stainless mounting components and a built-in splash guard (Waste King FAQ). Its parts diagrams also separate the threaded EZ Mount assembly from the Pro 3-Bolt assembly and clamp (EZ Mount L-1001 diagram, Pro 3-Bolt 9910 diagram).
Do not confuse two similar names. InSinkErator’s EZ Connect concerns the electrical connection, while Waste King’s EZ Mount concerns the sink-mount hardware (InSinkErator manual, Waste King EZ Mount manual). An electrical hardwire adapter cannot fix a sink-mount mismatch.
Take photographs before you start: the whole disposal, the identification plate and the mounting connection. Moen’s identification page puts the model and serial number on the plate label under the disposal and says warranty assistance requires the receipt, model number and serial number (Moen identification guide). Waste King’s removal instructions say to unplug the disposal or turn off the power at the breaker first, and to support the disposal as the mount ring is released or it may fall (Waste King EZ Mount manual). The three-photo routine is our own workflow built on those documents, not a service any maker offers.
Garbage Disposal Sink Mount: The Fit Chart
Each row comes from a maker’s own parts diagram, catalog or product page, except where the source column says otherwise. The limitation column is as important as the part number. “Not established” marks the edge of what the documents show. It does not mean the maker has declared the combination incompatible.
| Maker | Fits or does | Part number | Limitation | Source |
|---|---|---|---|---|
| InSinkErator | Residential Quick Lock replacement mounting assembly | QLM-00 / 72376D | Do not extend the residential fit statement to commercial installs or other brands | Product page, catalog |
| InSinkErator | Extended flange for compatible thick sinks, up to 1-3/4 inches documented | FLG-SSLG / 10082 | Adds flange reach; does not convert mount families. Accessory height is not allowable sink thickness | Catalog |
| InSinkErator | Mounting-gasket alternatives for specified applications | MGK-00 / 74657D | “Not for use with Evolution Series and E606 disposers.” | Product page |
| Moen | Mounting assembly documented for GXP33C, GXP50C and GX75C | 1824 | These diagrams do not prove it fits an existing Waste King Pro 3-Bolt assembly | GXP33C/GXP50C diagram, GX75C diagram |
| Moen | Separate sink flange shown for GX75C; also in the later GXP33C diagram | 1017 | A flange is not a complete mounting assembly | GX75C diagram, later GXP33C diagram |
| Waste King | Complete EZ Mount assembly documented for L-1001 and L-8000 | 1030 | Substitution for Pro 3-Bolt hardware is not established | L-1001 diagram, L-8000 diagram |
| Waste King | Complete Pro 3-Bolt assembly documented for 9910 | 3157AMC | Not the EZ Mount assembly | 9910 diagram |
| Waste King | Pro 3-Bolt cushion mount ring documented for 9910 | 1047AMC | One component, not the complete assembly 3157AMC; EZ Mount use not established | 9910 diagram |
| Waste King | Extended Pro 3-Bolt flange documented for 9910 | 3140AMC | Maximum sink thickness is disputed (see below) | 9910 diagram |
| Waste King | Adapter from an existing compatible three-bolt sink flange to an EZ Mount disposal | 3101AMC (3101 in retailer listings) | Reverse conversion is not established; direction detail comes from a specialty retailer, not a full maker chart | Waste King accessories, PlumbingSupply |
| GE | Adapter from an EZ Mount disposer to an existing three-bolt mount | PM3X214 | GE states: “This model is no longer being manufactured.” Do not count on availability | GE adapter page |
| Kohler | Disposal flange with stopper; Kohler’s sheet says it includes both | K-11352-CP | Accessory dimensions do not establish mount conversion or sink-opening size | Kohler drawing |
For sinks with a square opening, Kraus lists its GDA-1 adapter for Pax sinks and names most InSinkErator, Whirlpool and KitchenAid disposals (Kraus GDA-1). Ruvati lists its RVA1049ST extended flange for sinks up to 2 inches thick with a standard 3.5-inch opening, but its wording varies between “all” and “most” InSinkErator disposals, so get exact-model confirmation (Ruvati RVA1049ST).
Matched your mount to a row in the chart? Confirm the exact part against the maker's own documents for your disposal model before you buy, because a similar-looking mount does not decide it:
As an Amazon Associate, plumbingbythebook earns from qualifying purchases. Links below are affiliate links — they cost you nothing extra.
Cross-Brand Swaps and Where the Sources Disagree
The cross-brand question is the one that costs people a second trip to the store, and the makers speak to different interfaces. Moen says its GX75C fits most existing three-bolt assemblies, and expressly includes InSinkErator (Moen GX75C). Waste King separately says its Pro 3-Bolt mounting system cannot be retained for a Moen replacement, because the systems look similar but differ (Waste King FAQ). These statements are about different interfaces and do not contradict each other. “Most” is not “all,” so the rule is to check your own mount against the maker’s statement.
Reusing the old mount can be allowed. InSinkErator’s covered replacement procedure permits keeping matching mounting hardware, and Moen gives a reuse decision based on inspection (InSinkErator installation manual, Moen installation manual). Neither covers an unknown, damaged or merely similar mount. Reusing the mount also does not mean reusing the rest: Moen’s installation manual says not to reuse the existing discharge elbow and gasket, and to use only the new elbow, gasket, elbow flange and screws provided (Moen installation manual).
Three places where the documents do not line up:
Waste King 3140AMC thickness. The 9910 diagram identifies the part, but the thickness limit differs between Waste King’s own documents. The model drawing is read as 1/2 to 1-3/8 inches, and the general FAQ gives 1/2 to 1-1/4 inches for extended Pro 3-Bolt flanges. We cannot tell you why they differ. If your sink is thicker than 1-1/4 inches, get the exact part confirmed by Waste King before ordering (9910 diagram, Waste King FAQ).
MGK-00 and Evolution disposals. InSinkErator’s page says the gasket kit is not for Evolution Series or E606 disposers. A Home Depot listing title mentions Evolution Septic Assist, while its description repeats the exclusion, and a Lowe’s listing combines broad wording with specific exclusions. The maker’s restriction is the stronger evidence, so do not assume an Evolution exception (Home Depot listing, Lowe’s listing).
Older Moen part numbers. Moen’s November 2021 GXP33C diagram lists flange 1017, splash guard 205497 and stopper 186589 (Moen GXP33C diagram, Rev. 11/21). A December 2015 diagram lists 1823, 1822 and 1821 for the same three. These dated references do not prove that one replaced the other or that they are physically interchangeable. If you order single pieces, give Moen your model, serial and the diagram you are reading (later diagram, older diagram hosted by a distributor).
Professional opinions vary on whether to keep a serviceable compatible mount or replace the whole assembly. Gasket selection, clamp lubrication, locking methods, dishwasher-plug removal and electrical connections must follow your exact model’s instructions. They differ between systems. Waste King’s EZ Mount allows its rubber gasket on stainless sinks and requires sealant for other materials, not both. Its Pro 3-Bolt calls for liquid soap on the cushion’s inside lip, while the EZ Mount manual authorizes controlled hammer taps on the mounting-ring ears (EZ Mount manual, Pro 3-Bolt manual).
Serial Numbers and Date Codes
Serial numbers help less here than they do for faucets. InSinkErator changed its serial format in summer 2024, according to its warranty page. For the older numeric format, the first two digits are the year and the next two the month, and that rule must not be applied to the newer alphanumeric format (InSinkErator warranty). A serial number dates a unit. It does not tell you the mount type.
GE describes a serial beginning with two letters, then six numbers and a final letter. The first letter stands for the month and the second for the year (GE date-code guidance). Year letters repeat: GE’s chart assigns A to 2025, 2013 and 2001, and D to 2026, 2014 and 2002. So a matching code alone does not date the unit or identify its mounting parts. Use the scheme only when your serial matches the documented format.
We did not verify a public disposal date-decoding formula for Moen, Waste King or Joneca. That means we did not establish one, not that none exists. Record the complete serial and ask support to read it, and do not borrow a faucet serial format (Waste King Pro 3-Bolt manual).
If You Cannot Find the Brand
When the label is gone, check the whole installation rather than only whether the old motor hangs. InSinkErator’s installation manual covers sink thickness (it requires an extended sink flange above 3/4 inch), whether the new mounting assembly is the same as the old, and the distance from the bottom of the sink to the center line of the disposer outlet (InSinkErator installation manual). Moen’s selection guide has you check the height between the sink and the cabinet floor and where your drain and dishwasher pipes line up (Moen: Choosing a Garbage Disposal). So a matching mount does not establish that the outlet fits your surrounding plumbing.
Lookup tools work from a model, not a photo. Waste King’s downloads page lists its spec and parts sheets by model under EZ Mount and Pro 3-Bolt Mount headings (Waste King downloads). We found no photo-recognition service from any of these makers (Waste King downloads, Joneca owner manuals).
If identification stays unresolved, replacing the disposal with a new one that comes with its own mounting assembly is a real option once you have checked dimensions. The Moen GX75C, for example, includes a flange and mounting assembly (Moen GX75C). We found no verified disposal-mount adapter from Danco or BrassCraft, and a generic drain connector is not a substitute for a mount.
Be careful with very old units. PlumbingSupply warns that listed Waste King parts may not fit pre-1996 units and describes a floor-facing reset switch as a legacy clue. That is a specialist retailer’s note, not a maker’s dating rule, so confirm before relying on it (PlumbingSupply).
When to Call a Plumber
A professional is useful when identification means releasing a mount you cannot read, checking damaged hardware, or settling thickness and drain geometry. That is our recommendation, based on the support and drainage requirements in the makers’ documents. InSinkErator requires the drain connection to sit below the discharge, with at least 1/4 inch of pitch per foot toward it (InSinkErator installation manual). Waste King’s instructions refer electrical uncertainty to a qualified electrician (Waste King EZ Mount manual).
We found no verified national price for an identification call, so do not trust a flat figure. Local examples show how terms vary. Knight Plumbing advertises $99, waived when you proceed with a repair (Knight). Rooter-Pal lists $99 to $189 for a standard service call and diagnosis (Rooter-Pal). According to Carter’s My Plumber, its diagnostic fee is $79, credited toward an approved repair (Carter’s). These are three providers, not a survey. Ask yours about diagnostic charges, minimums and repair credits, and ask for a written note of the existing mount, the proposed disposal, the exact adapter or assembly, the thickness allowance and any drain changes.
What to Do Next
Write down the disposal’s complete model, which mount family you have, and your sink’s thickness. Match all three to the chart, then to the maker’s documents for your exact model before you order.
Is an EZ Mount disposal the same as a three-bolt mount?
No. Waste King describes EZ Mount and Pro 3-Bolt as different systems, with different materials and splash guards. An adapter exists for connecting a compatible existing three-bolt flange to an EZ Mount disposal, but the reverse is not established.
Will a Moen disposal fit my old InSinkErator mount?
Moen says its GX75C fits most existing three-bolt assemblies and names InSinkErator. “Most” is not “all,” so check your mount against Moen’s statement and the installation manual before you remove anything.
Can I reuse my old sink flange and mounting hardware?
Sometimes. InSinkErator’s installation manual allows keeping matching mounting hardware (InSinkErator installation manual), and Moen’s installation manual bases reuse on inspecting the existing mounting ring seals (Moen installation manual). Neither covers an unknown, damaged or merely similar mount, and Moen’s installation manual still has you use the new discharge elbow, gasket, elbow flange and screws (Moen installation manual).
Does the GE PM3X214 adapter still exist?
GE’s page says that model is no longer being manufactured. Do not plan a repair around it without confirming a seller has stock.
Can I find my mount type from a serial number?
No. InSinkErator publishes a serial date format on its warranty page (InSinkErator warranty), and GE publishes a serial date code for its appliances (GE date-code guidance). Those only date the unit. The model and the mounting assembly decide the order.
Sources
- Waste King: Support FAQ
- Waste King: Support downloads
- Waste King: Residential accessories
- Waste King: L-1001 parts diagram
- Waste King: L-8000 parts diagram
- Waste King: 9910 parts diagram
- Waste King: EZ Mount installation manual
- Waste King: Pro 3-Bolt installation manual
- InSinkErator: Quick Lock mounting assembly
- InSinkErator: Accessory catalog
- InSinkErator: Mounting gasket kit
- InSinkErator: Power installation, care and use manual
- InSinkErator: Warranty and label guide
- Moen: Choosing a Garbage Disposal
- Moen: Garbage Disposals identification guide
- Moen: GX75C
- Moen: GX75C parts diagram
- Moen: GXP33C and GXP50C parts diagram
- Moen: Later GXP33C parts diagram
- Moen: Installation manual
- Moen: Store listing for 1039
- GE Appliances: PM3X214 adapter kit
- GE Appliances: Disposer model and serial locator
- GE Appliances: Date-code guidance
- Joneca: Owner manuals
- KitchenAid: Owner center
- Kohler: K-11352 specification
- Kraus: GDA-1 garbage disposal adapter
- Ruvati: RVA1049ST extended flange
- Home Depot: Moen 1039 sink flange kit
- Home Depot: InSinkErator MGK-00 listing
- Lowe’s: InSinkErator gasket listing
- PlumbingSupply: Waste King disposer parts listing
- Northern Plumbing: Older Moen GXP33C diagram
- Knight Plumbing: Quote terms
- Rooter-Pal: Residential plumbing pricing
- Carter’s My Plumber: Price estimator
Educational content only. Not a substitute for licensed professional advice. Local plumbing codes vary by jurisdiction. Use of any guidance from this guide is at your own risk.
Parts for this repair
As an Amazon Associate, plumbingbythebook earns from qualifying purchases. Links below are affiliate links — they cost you nothing extra.
- InSinkErator QLM-00 Quick Lock Mounting Assembly (search by part number) — InSinkErator lists QLM-00 (72376D) as its residential Quick Lock replacement mounting assembly. The maker's fit statement is residential only, so do not assume it suits commercial installs or another brand's disposal.
- InSinkErator FLG-SSLG Extended Sink Flange (search by part number) — InSinkErator lists FLG-SSLG (10082) as an extended flange for compatible thick sinks, with a documented maximum sink thickness of 1-3/4 inches. It extends flange reach and does not convert one mount family to another.